Multivalent-effect immobilization of reduced-dimensional perovskites for efficient and spectrally stable deep-blue light-emitting diodes
Related Articles
Multiple defects renovation and phase reconstruction of reduced-dimensional perovskites via in situ chlorination for efficient deep-blue (454 nm) light-emitting diodes
Deep-blue perovskite light-emitting diodes (PeLEDs) based on reduced-dimensional perovskites (RDPs) still face a few challenges including severe trap-assisted nonradiative recombination, sluggish exciton transfer, and undesirable bathochromic shift of the electroluminescence spectra, impeding the realization of high-performance PeLEDs. Herein, an in situ chlorination (isCl) post-treatment strategy was employed to regulate phase reconstruction and renovate multiple defects of RDPs, leading to superior carrier cooling of 0.88 ps, extraordinary exciton binding energy of 122.53 meV, and higher photoluminescence quantum yield of 60.9% for RDP films with deep-blue emission at 450 nm. The phase regulation is accomplished via fluorine-derived hydrogen bonds that suppress the formation of small-n phases. Multiple defects, including halide vacancies (shallow-state defects) and lead-chloride antisite defects (deep-state defects), are renovated via C=O coordination and hydroxy-group-derived hydrogen bonds. Consequently, deep-blue PeLEDs with a record maximum external quantum efficiency of 6.17% and stable electroluminescence at 454 nm were demonstrated, representing the best-performing deep-blue PeLEDs.
Fluorine-modified passivator for efficient vacuum-deposited pure-red perovskite light-emitting diodes
Vacuum-deposited perovskite light-emitting diodes (PeLEDs) have demonstrated significant potential for high-color-gamut active-matrix displays. Despite the rapid advance of green PeLEDs, red ones remain a considerable challenge because of the inferior photophysical properties of vacuum-deposited red-light-emitting materials. Here, a rationally designed fluorine-modified phosphine oxide additive was introduced to in-situ passivate vacuum-deposited perovskites. The highly polar 2-F-TPPO incorporated perovskite films demonstrated enhanced photoluminescence quantum yield (PLQY), suppressed defects, and improved crystallinity. When implemented as active layers in PeLEDs, an external quantum efficiency (EQE) of 12.6% with an emission wavelength of 640 nm is achieved, which was 6 times higher compared to the previously reported most efficient vacuum-deposited red PeLEDs (EQE below 2%). Our findings lay the foundations for the further exploration of high-performance vacuum-deposited PeLEDs toward full-color perovskite displays.
Promises and challenges of indoor photovoltaics
Indoor photovoltaics (IPVs) harvest ambient light to produce electricity and can cleanly power the rapidly growing number of Internet-of-Things (IoT) sensors. The surge in IPV development, with new proposed materials, devices and products, creates the need to critically evaluate how IPV devices have advanced and to assess their prospects. In this Review, we analyse the status, challenges and opportunities of established and emerging IPV technologies, including metal-halide perovskite, organic photovoltaics, dye-sensitized solar cell and perovskite-inspired materials. Many emerging low-toxicity semiconductor materials could reach IPV efficiencies of up to 50%, but carrier localization and defect trapping hinder their performance. Wide adoption of standardized performance assessment methods is essential, and further harmonization is needed for stress tests, qualification standards and energy rating assessments. For seamless IPV integration in IoT devices, series-connected cell modules and appropriate power management hardware are crucial to maximize energy extraction. IPV device stability, technology upscaling and cost-effective integration in IoT sensors must be further developed but balanced with sustainability across the entire value chain.
Surfactant-induced hole concentration enhancement for highly efficient perovskite light-emitting diodes
It is widely acknowledged that constructing small injection barriers for balanced electron and hole injections is essential for light-emitting diodes (LEDs). However, in highly efficient LEDs based on metal halide perovskites, a seemingly large hole injection barrier is usually observed. Here we rationalize this high efficiency through a surfactant-induced effect where the hole concentration at the perovskite surface is enhanced to enable sufficient bimolecular recombination pathways with injected electrons. This effect originates from the additive engineering and is verified by a series of optical and electrical measurements. In addition, surfactant additives that induce an increased hole concentration also significantly improve the luminescence yield, an important parameter for the efficient operation of perovskite LEDs. Our results not only provide rational design rules to fabricate high-efficiency perovskite LEDs but also present new insights to benefit the design of other perovskite optoelectronic devices.
Polycystin-1 regulates tendon-derived mesenchymal stem cells fate and matrix organization in heterotopic ossification
Mechanical stress modulates bone formation and organization of the extracellular matrix (ECM), the interaction of which affects heterotopic ossification (HO). However, the mechanically sensitive cell populations in HO and the underlying mechanism remain elusive. Here, we show that the mechanical protein Polysyctin-1 (PC1, Pkd1) regulates CTSK lineage tendon-derived mesenchymal stem cell (TDMSC) fate and ECM organization, thus affecting HO progression. First, we revealed that CTSK lineage TDMSCs are the major source of osteoblasts and fibroblasts in HO and are responsive to mechanical cues via single-cell RNA sequencing analysis and experiments with a lineage tracing mouse model. Moreover, we showed that PC1 mediates the mechanosignal transduction of CTSK lineage TDMSCs to regulate osteogenic and fibrogenic differentiation and alters the ECM architecture by facilitating TAZ nuclear translocation. Conditional gene depletion of Pkd1 or Taz in CTSK lineage cells and pharmaceutical intervention in the PC1-TAZ axis disrupt osteogenesis, fibrogenesis and ECM organization, and consequently attenuate HO progression. These findings suggest that mechanically sensitive CTSK-lineage TDMSCs contribute to heterotopic ossification through PC1-TAZ signaling axis mediated cell fate determination and ECM organization.
Responses